Adding Hardware to Garage Doors

If you are thinking of adding hardware to your garage door, you’ve come to the right place. In this article, you’ll learn how to add decorative hardware to a garage door, including how to choose the right kind of hardware, how to position the handles, and how to install the hinges. Then, you can add a lock to your garage door, too! And, don’t forget to decorate your door with the right colors and design!

Installing decorative hardware on a garage door

Decorative handles on a garage door make the entrance to the garage look more stylish. Install the handles several inches in from the door’s edge. Use a painters tape to mark the location of the handle. Remember to leave enough room for the handle’s width and length. Handles are typically installed in pairs. The lower panel of the door must be leveled with the ground before installing the handles.

When installing decorative hardware on a garage door, you need to think about the design of the door itself. The decorative hardware should complement the style of the home, as rustic looking hardware may look too outdated on a modern home. You also need to choose hardware that is in the same “family” as the rest of your home’s decorative hardware. Finally, keep in mind that the garage door should still be functional. Otherwise, it will be useless.

The best decorative hardware for a garage door can add a distinctive touch to the exterior of a house. There are many types of decorative hardware to choose from, such as cross rails, cross bucks, panels, hinges, handles, knobs, and other accessories. The choices are limitless. Just make sure the design is in proportion to the garage door’s width and height. And remember that decorative hardware should not extend above the door’s shoulder height.

Once you’ve measured your garage door and have the appropriate hardware, you can start assembling the decorative hardware. First, drill holes in the exterior shell of the garage door. For fiberglass or aluminum doors, drill the holes slowly and stop the drill when the bit pierces the surface. For wooden doors, drill holes deep enough for screws included in the kit. Once the screws are in place, tighten the screws with a screwdriver to ensure that they don’t strip the surface of the door. Remember to never overtighten screws because it can cause damage.

Choosing the right type of hardware

While decorative hardware isn’t required for every garage door, decorative strap hinges are an essential addition for swinging doors. Made of thick steel, they can withstand the weight of the garage door and remain sturdy for years. Heavy-duty strap hinges are also available that mount directly to the wall or frame. These are great options if you have a steel, hollow-block, or brick frame.

Before shopping for door hardware, you must know the prep of your door. Your door’s backset (the distance from the bore hole to the edge of the door) is an important factor to consider. Some door hardware has adjustable backsets, but you’ll need to specify this when choosing hardware. A standard door prep measures two 1/8″ in diameter with a one-inch cross bore. If your door has a different prep, contact the door hardware manufacturer. If your door is a bit thicker, you’ll need to buy a different kind of hardware.

High-quality wrought-iron or bronze are elegant and durable options, while low-cost materials like aluminum and vinyl are cheaper and less beautiful. Metals should be powder-coated to protect them from rusting or chipping. Materials can be hardy in some climates, and choosing the right type of hardware will ensure your door is protected from harsh weather conditions. For best results, visit a dealer showroom or visualize your new door using an online visualization tool.

Once you have decided on a style, consider how often you’ll use your garage door. The most common hinge styles are ball-bearing and disc-bearing. The weight limit of these hinges will depend on how frequently they are used. For heavier garage doors, you may want to consider strap hinges. If you choose to install hinges yourself, be sure to check the weight limits on the doorway frame.

Positioning the hinges

The most common mistake with a garage door is the wrong hinge. To install a new one, you should start by loosening the hinge bolt nuts. Then, position the hinge over the horizontal joints and tip it outwards to disengage the roller from the track. If you cannot find the correct hinges for your door, you can use a socket set to remove them. You should repeat the process for each hinge.

To start, check the hinges. If they are loose, you may need to tighten the screws. The hinges on a garage door should be level with the floor. Make sure that there is no rust or crack on the hinges. If you see any cracks or corrosion on the hinges, you should replace them. If you haven’t yet, you can contact a professional to repair the hinges for you.

To identify the type of hinge you need, measure each hinge in the garage door. The numbers will indicate which hinge is the center one. Hinges on the edges of the door hold the rollers. You should also measure the distance from the bottom of the hinge to the center of the top circle. Then, lay the hinge in its proper place. After lining up the hinges, adjust the panel and replace the hinges as needed.

Garage doors come with numbers indicating how to position the hinges. For example, the #1 hinge should be in the middle of the garage door. Likewise, the second hinge should be in between the second and third panels. The third hinge should be in between the third and fourth panels. In addition to the number, you must consider the thickness of the steel hinge. The thicker the hinge, the greater its weight support.

Positioning the handles

Using painters tape, identify where the hardware will go. Place the handles in pairs. Typically, they’re located on the second door panel from the ground. If you can’t locate the handles, use a washable marker to mark their location. Next, cut the painters tape to the appropriate length. If they’re too long, you can cut it into even pieces. After cutting the tape, position the handles as desired.

Before installing the handles, make sure the screws are in the right locations. The iron handle set is located on the second panel of the door, the “lock” section. Make sure it clears the opening. If it doesn’t, drill a new hole. Then, use a 1/16″ drill bit to drill through the exterior metal door skin. Be careful not to over-drill. If your door is made of wood, drill the holes at least 1/16 inch before attaching the handles.

The height of the handles depends on the type of door and the placement. The handles must be between 48 to 54 inches high for easy access. In commercial projects, it may be necessary to research door handle heights. One manufacturer of door hardware, SOSS Hardware, points to the ADA in its guidance. For more information, check out the ADA bill. It contains more detailed guidance regarding door handle heights. The height of the handles on garage doors varies from individual to individual.

When installing new door handles, you need to remember that the process shouldn’t take more than a few minutes. Using a drill and tape measure, you’ll be able to install the handles in the proper places. Keep in mind that some doors come with pre-drilled holes; others are hung by the user. Using these guidelines will ensure smooth operation of the door. And, most importantly, it will make your new door handles feel more comfortable.

Did you miss our previous article…
http://yardworship.com/how-to-make-the-most-of-real-estate-hashtags/