Connect with us

CURB APPEAL IN WINTER

Chic DIY Copper Magazine Holder: How to Make this Surprisingly Easy Piece

Copper is one of the hottest metals being used in design these days. It’s everywhere, in all rooms, in all amounts. While it might seem a little intimidating to attempt a DIY project using metal, pipes craft are one of the fasted and easiest ways to get started. Truly, you can start and finish your…
The post Chic DIY Copper Magazine Holder: How to Make this Surprisingly Easy Piece appeared first on Homedit.

Avatar

Published

on

Add your four 4” pipes to the Ls attached to the 20” pipes. Set aside.

Step-by-Step Instructions to Create a Magazine Rack for Your Home

The post Chic DIY Copper Magazine Holder: How to Make this Surprisingly Easy Piece appeared first on Homedit.
Connect your 20” segments to the Ts, so that you end up with a frame.

DIY Project: Copper & wool felt magazine holder, 20”w x 7”d x 16”h

DIY Level: Beginner

Prepare the fabric for the magazine rack

Materials Needed to Create a DIY Copper Magazine Holder:

  • Two (2) 1/2″ copper pipe, 20” long
  • Four (4) 1/2″ copper pipe, 12” long
  • Four (4) 1/2″ copper pipe, 7” long
  • Four (4) 1/2″ copper pipe, 4” long (Note: 10’ and 2’ lengths of 1/2″ copper pipe will provide all of these pieces, with a little bit left over.
  • This was the most cost-effective method I could calculate.)
  • Four (4) 1/2″ copper Ts
  • Four (8) 1/2″ copper Ls
  • 36” x 18” piece of wool felt
  • Metal glue – not shown (optional but recommended)

Enjoy your stylish new organizational system!

Step 1: Assembling the Copper Frame of Your Magazine Rack

Freestanding copper magazine rack diy
Sew your felt magazine holding piece. Fold over the short end of your 18” x 36” piece of wool felt 1-3/4”. Pin this fold every couple of inches all the way across.
Squeeze a bit of glue on the inside rim of any connector pieces that are loose, then twist and secure the pipe ends inside. IMPORTANT: DO NOT GLUE YOUR 20” PIPES OR THE ADJACENT L CONNECTORS YET. You need to be able to remove the 20” pipes to add your felt magazine holder, so it’s important that these pieces can come off at this point.
Connect the 7” pipes with Ts to the ends of the 12” pipes that you just added.
Load with magazines and place next to the sofa. When the adhesive has completely set and dried, you’re done!
Sew a double seam about 1/4″ from the “raw” end of your folded-over felt. To do this with a basic sewing machine, simply sew one seam, cut threads, and go back and sew another seam very close to the first.
Squeeze a bit of glue
DIY Copper Mag Rack
Diy copper magazine rack materials
Floor DIY Copper Mag Rack

Step 2 (Optional): Glue Your Copper Frame Together

Add your four 12” pipes to the Ls attached to the 7” pipes.
While we’ve added this magazine rack to our living room, we think this would be an excellent solution for a study or playroom. You’ll probably love this addition to your home so much that you’ll come back again to make a few more. We believe this is a great option for older kids and teens, who may have comic books or magazines that end up all over their bedroom or playroom floor. Finally, another fun use of this copper magazine holder is to place it by your entryway to collect mail and newspapers.
Felt magazine holding piece
Assemble copper frame

Step 3: Sewing the Felt Magazine Rack Holding Piece

Closer look to the copper magazine rack
Four copper pipes
We think it looks great – simple and classic – next to a living room sofa. But wherever you choose to put your copper magazine holder, we think you’ll be pleased with your DIY pipes craft.
Assemble final pieces. Slide your 20” pipes through the felt seams, then secure the pieces with your metal adhesive (if needed). Take care to keep glue off your wool felt. Set up your magazine holder squarely against a wall and let the adhesive dry and harden completely up to 24 hours.
Connect pipes

Step 4: Assembling the Final Pieces of the Magazine Holder

Glue PARTS of your copper frame together. If your copper pipes fit snugly into the connector pieces (e.g., the Ts and Ls), then you can skip this step and move on to Step 3. But if your frame is a bit wobbly and loose, you’ll want to secure the connections with some adhesive appropriate for metals. I used Loctite GO2 Gel.
Copper is one of the hottest metals being used in design these days. It’s everywhere, in all rooms, in all amounts. While it might seem a little intimidating to attempt a DIY project using metal, pipes craft are one of the fasted and easiest ways to get started. Truly, you can start and finish your own custom copper magazine holder in no time at all. As far as DIYs go, this one is very satisfying…especially if your living room is in desperate need of a clean-lined, understated spot to stow away your magazines and other reading materials!

Step 5: Find a New Home for Your Magazine Rack

Glue copper parts
Simple and classic copper magazine rack
Assemble fina copper pieces
Assemble the copper frame. Start by adding Ls to both ends of your two 20” and two 7” pipes. Add the middle part of the Ts to both ends of your last two 7” pipes.
Copper set aside
Repeat Step 3 on the other short end of your felt piece.
As you can see, this project only took a few simple steps to complete, and then you’ll be good to go. We love the industrial yet chic look of the copper pipes, which are then balanced out with the darker material. Of course, adjust the style and color of this piece to fit your home décor, and you’ll have a functional yet stylish item to add to your home this year.
Connect all copper tubes

Continue Reading

YardWorship.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a way for websites to earn advertising revenues by advertising and linking to Amazon.com or .ca, .co.uk, etc.