Drilling Through Tile Can Be an Easy DIY

The best way to drill through tile is to always use a low speed and start slowly. You never want to go too fast or hard on tile, because you can crack it and overheat the drill bit.
You’ll need different drill bits for different tiles. Carbide-tipped masonry bits work best for standard ceramic tile. The best drill bits to drill through porcelain tile or glass tile are diamond-tipped bits.
After you successfully drill through the glazed surface of the tile, you can drill a bit faster. You can also add a little pressure to get through the rest of the tile to the wall.

Easy Steps For Drilling Through Tile

There are a few options for ways to do this.
You’ll also want to use a level to make sure that the marks on the masking tape are properly located. No one wants a crooked tile bar!

1. What kind of tile do you have?

To prevent scratching your tile, always use light pressure when drilling. Pushing down too hard can make the drill bit slip and make a big scratch on the tile surface.
Remove any masking tape that you used. With a wet cloth, wipe down the tile to clean off any dust particles or debris that came from the drilling. Finally, insert your wall anchors or plugs and attach the bathroom accessory.
Drilling through tile is a little different in that you need to keep the drill bit cool. As it makes its way through the tile, it gets hot and can overheat.

• Porcelain tile is harder than ceramic. So when considering how to drill through porcelain tile, you’ll have to push harder to break through. You’ll also need special drill bits that can get through the glaze as well as the porcelain. The same holds true for stone tiles too.
• Ceramic tiles are not quite as hard but they are indeed slippery. When drilling through glazed ceramic tile, you’ll need the right tile drill bit and a few tips to keep the drill from sliding on the surface of regular ceramic tile.
• Glass tiles are also challenging due to their slippery surface. Glass tile material is also more susceptible to scratches and blemishes if the drill bit slides.

2. Use the correct drill bit

It also helps avoid overheating. You’ll also want to use a fresh, new diamond-tipped drill bit.
When you reach the wall surface behind the tile, maintain the slow drill speed to keep the wall intact. You want your wall anchor to sit properly in the hole. Also, many experts recommend changing to a regular drill bit once you reach the wall.

Carbide-tipped drill bits are the most common type used to drill through tiles. This type is best for regular ceramic tiles and natural stone tiles, but not for porcelain tiles. Carbide-tipped bits just aren’t as strong as a diamond-tipped drill bit.
Measure the spots for the drilling points and mark the locations with an X. The masking tape will create some tension when you start drilling and it’s just enough to keep the drill bit from slipping.

3. Gather up the proper tools

• Masking tape
• Level
• Tape measure
• Marker
• Sponge or cloth
• Dust mask
• Safety goggles
• Latex safety gloves

4. Measure and mark the hole locations

That said, it’s not a difficult process to drill tiles. You just need the right tools and some patience to know how to drill through tile without cracking it.
However, it doesn’t have to be scary. If you follow the recommended steps and go slowly, you can install your towel bars and bathroom accessories without fear.
Drilling through tile can be the most frightening part of a DIY project for many people. One wrong move and you crack the tile.
The post Drilling Through Tile Can Be an Easy DIY appeared first on Homedit.
Diamond-tipped drill bits are certainly more expensive. Of course, they are also super durable. You can depend on this drill bit to get through hard tiles. These are good for porcelain tiles and they don’t burn out as easily as carbide bits.
The proper types for tile drill bits are diamond-tipped drill bits or carbide-tipped drill bits.
Certain kinds of tile require specific drill bits. Pay attention to the recommendations so that you’ll have success when drilling your tile.
The exception is when it has a polished, glazed surface, which makes it harder to drill. In those cases, a diamond tip is the best bet.

5. Drill the tile

Travertine is a natural stone that is part of the limestone family. The soft, porous stone is easy to drill with masonry bits.
Recommendations are to ruin the drill at 100-200 RPMs. This speed will help you bore through the tile without creating strong vibrations that can crack the tile.
The hammer drill motion will crack any kind of tile. It might work for brick and stone, but certainly not for tile.
Knowing the type of tile material you are working with is critical. Understanding a bit about materials in your newly tiled bathroom is key so that you can choose the right tools and drill bits.

The moment of truth! When the holes are marked and measured, it’s time to drill. The first and most important piece of advice is to take your time and go slowly. The tiles are tough so it’s easy to go all out right away and drill fast. But, that’s the quickest way to damaged tile.
Before you start drilling, you can make things easier and a little more stable. Try this trick: Use masking tape on the tile surface where you want to make the holes.
Tile requires some specific tools and techniques. We’ve got the process laid out so you’ll be drilling through tile like an expert. Of course, it pays to remember that even pros can make a mistake!

6. Keep the drill bit cool

Also, carbide drill bits will stop when they overheat, but diamond bits will still work as long as you cool them.
Before you start drilling, it’s critical to choose the right tile drill bit. You’ll want to use brand new bits too. A used bit — or the wrong drill bit — can mean tile cracking. Older bits can be less efficient and are far more likely to damage the tile.
No! You should never use hammer drills for tile. It is also called a percussion drill or impact drill. While it’s used mainly for drilling hard materials, it is not used for drilling tile.
Porcelain tiles are the hardest tile surfaces. The manufacturing process makes porcelain as hard as stone. It also has a higher silica content than ceramic tile, however, which also makes it brittle. That’s why you can’t use tile cutters for porcelain.

• Use a wet sponge. By holding a wet sponge under the drill bit, you can keep it cool. It also has the added benefit of catching some of the tile dust. If you’re working solo and can’t hold it against the tile whilst drilling, choose another option.
• Spray water on it. It also works to stop drilling periodically and spray some water on the drill bit. Just be sure to keep water away from the power drill motor.
• Commercial spray systems to keep bits cool are available if you’re going to be doing a lot of tile drilling.

7. Clean up the tiles

Once you start drilling slowly, you’ll want to add some pressure gradually. Too much pressure all at once will break and crack the tile.
In addition to the proper bits, you need a single power tool: a good power drill. You’ll also want to have these things on hand, including the correct protective equipment.

Drilling through a ceramic tile: Conclusion

Diamond tips help the bit get through the tough surface of the tile without cracking. That is if you drill slowly and properly. The diamond tip style is also good for ceramics, but is not necessary.
Also, never use regular drill bits for tile — they’re just not strong enough.

Avoid this by being sure to drill slow and by keeping the drill bit cool. You can either occasionally dab it with a wet sponge, spray some water on it or dip it in some cutting oil.